2024 SeaValue Premium - Flipbook - Page 151
Electrical
E SERIES BATTERY SWITCH
350 Ampere continuous rating
for inboard gasoline and diesel
engines. One-piece tin-plated
copper stud design never loosens
over time. Terminal studs accept
3 / " or M10 ring terminals. Ignition
8
protected and UL Listed. Selector
features make-before-break
contact design. Color: Red.
9001E
Type
1, 2, Both, Off,
ON-OFF,
Special
59.99 EA
59.99 EA
ML-SERIES HD REMOTE BATTERY SWITCH
Allows high amp switching under load from remote
locations or manually, eliminating long cable runs. Includes
remote control switch # 2145 with lockout slide to prevent
accidental switching. 12V DC coil controls circuits up to 32V
DC and is rated for 500 amps continuous duty and 2500
cranking amps (10 sec.) to handle even large diesel engines.
Magnetic latch only draws current when changing the state
of switch: it draws no current in the "ON" or "OFF" states. 3/8"
Tin plated copper studs.
Item#
Special
661-7700
269.99 EA
701 SURFACE OR RECESS MOUNTED
CONTOUR MANUAL BATTERY MASTER SWITCH
• Compact, lightweight
• Removable key
• Countersunk recesses for surface mount application
• Standard 21/16" (52 mm) hole cut out (same as standard
gauge hole)
• Inside: captive inserts for 3/16" (4.8 mm) nuts providing full
access for cables with no restrictions
• Standard interchange label system
• Molded in high temperature, fiber reinforced plastics
Item#
969-701c
ST-BLADE BATTERY TERMINAL MOUNT
FUSE BLOCK
Easy to install 4 ATO®/ATC® fused circuits mounts directly on
the battery terminal studs. Screw terminals for securing wires
with insulated ring terminals and covers included.
• Screw terminals for securing wires
• Accepts small format labels
• Insulating cover meets ABYC/USCG insulation requirements
• Ignition Protected - for use in a gasoline engine
compartment
• Includes 4 write-on circuit labels
• Includes four 16-14 AWG and four 12-10 AWG Nylon
insulated ring terminals
9003E
Item#
661-9001E
661-9003E
Mount
Surface or Recessed
Volts
6-48
Size
23/4" x 23/4" x 3"
• Fuses sold separately
5024 includes a 4-circuit negative busbar
Item#
661-5024
TERMINAL BLOCK
6 Gang
Volts
6-48
Size
23/4" x 23/4" x 3"
POWERPOST CABLE CONNECTOR
Connect high amperage cables securely. Includes insulator
caps. 48 volts DC maximum. Posts have no amperage
rating because amperage flows between terminals stacked
on the post and is determined by the wire and terminals
used.
Stud Size
3
/8" x 7/8''
Size
3.30'' x 1.75''
Special
17.99 EA
17.99 EA
DUAL POWERPOST CABLE CONNECTOR
Special
59.99 EA
Item#
661-2018
Terminal/Fuse Blocks and Buss Bars
10 Gang
Corrosion resistant construction. Moisture repellent bakelite insulator base. Nickel
plated brass terminals and #8-32 screws. Protective insulator barrier strips. Rated
for 30A @12V.
Special
Item#
Gangs
Size
4
4"L x 15/16"W x 11/16"H
6.99 EA
50-13561c
50-13571c
6
43/8"L x 15/16"W x 11/16"H
9.99 EA
50-13581c
8
51/2"L x 15/16"W x 11/16"H
8.99 EA
50-13591c
10
65/8"L x 15/16"W x 11/16"H
9.49 EA
• Rated for 200 amps continuous, 300 intermittent, 1000 cranking
• Panel mount version requires a standard 11/16" cut out
Mount
Surface or Recessed
8 Gang
4 Gang
Item#
661-2002
661-2003
4 POSITION - OFF/1/BOTH/2
The 701-S is the most compact selector switch available
on the market. Housed in the same manner as the 701 and
includes the same removable side plates and back cover.
While BEP Marine foremost recommends isolated battery
systems as outlined with our distribution clusters, the
701-S offers a simple economical way of separating two
batteries.
Item#
969-701Sc
Special
46.99 EA
Special
49.99 EA
701-S MINI BATTERY SELECTOR SWITCH
149
Provides a termination point for extending the length of
outboard harnesses or other conductors.
• Designed for connecting high amperage conductors
• 2018 is also designed for outboard engine installation
when factory cables need to be extended
• One-piece serrated flange nuts ensure correct and secure
connectionsSpecifications:Continuous Rating Not ratedamperage flows between terminals stacked on post and is
determined by wire and terminals used.
• Voltage Max. Operating: 48V DC
• Mounting Holes Accepts: #10 (M5) Screws
• 2.75''L x 1.75''H
Special
27.99 EA
TERMINAL BLOCK
BATTERY TERMINAL MOUNT BUSBARS
4-Gang
Tin plated copper bus handles voltage up to 32VDC and is
rated for 100 Amps. #8-32 Screw terminals w/captive star
lock washers ensure a good connection.
Item#
Special
661-2340
29.99 EA
KEY: Blue Item # =NEW
|
Red Item # =HAZARDOUS
| vOversize |
6-Gang
A closed back design completely insulates power from the mounting surface. Each
screw pair is one isolated circuit. Optional jumpers allow creation of common
circuits. Tin-Plated Brass.
Item#
Gangs
Amps
Fastener
Special
661-2404
2
20
#6
5.99 EA
661-2406
6
20
#6
8.99 EA
661-2504
4
30
#8
8.99 EA
661-2506
6
30
#8
9.99 EA
To Our Valued Customers: Prices are subject to change without notice
