2024 SeaValue Canada Premium - Catalog - Page 151
Electrical
Terminal/Fuse Blocks and Buss Bars
MINI ADD-A-BATTERY
The Add-A-Battery includes a Dual Circuit Plus™ Battery
Switch and an automatic charging relay. These components
simplify switching and automate charging, so that all you
have to do is turn the battery switch ON and when you
board and OFF when you leave. For outboard and inboard
powered boats. Includes #6011 M-Series mini dual circuit
plus battery switch and #7601 automatic charging relay.
Item#
661-7649
Amps
65
BATTERY TERMINAL MOUNT BUSBARS
Tin plated copper bus handles voltage up to 32VDC and is
rated for 100 Amps. #8-32 Screw terminals w/captive star
lock washers ensure a good connection.
Item#
661-2340
44.99 EA
234.99 EA
ST-BLADE BATTERY TERMINAL MOUNT
FUSE BLOCK
ADD A BATTERY (DUAL CIRCUIT SYSTEM)
Simplifies switching and automates charging for a
complete two battery bank solution.
Package includes:
e SERIES DUAL CIRCUIT PLUS™ BATTERY SWITCH.
Simplifies Battery Switching, Isolates engine and house
circuits and combines battery banks for emergency
starting
Item#
661-7650
Amps
120
318.99 EA
ML-SERIES HD REMOTE BATTERY SWITCH
Allows high amp switching under load from remote
locations or manually, eliminating long cable runs. Includes
remote control switch # 2145 with lockout slide to prevent
accidental switching. 12V DC coil controls circuits up to
32V DC and is rated for 500 amps continuous duty and
2500 cranking amps (10 sec.) to handle even large diesel
engines. Magnetic latch only draws current when changing
the state of switch: it draws no current in the "ON" or "OFF"
states. 3/8" Tin plated copper studs.
Item#
661-7700
Item#
661-5024
Easy to install 4 ATO®/ATC® fused circuits mounts directly on
the battery terminal studs. Screw terminals for securing wires
with insulated ring terminals and covers included.
• Screw terminals for securing wires
• Accepts small format labels
• Insulating cover meets ABYC/USCG insulation requirements
• Ignition Protected - for use in a gasoline engine
compartment
• Includes 4 write-on circuit labels
• Includes four 16-14 AWG and four 12-10 AWG Nylon
insulated ring terminals
• Fuses sold separately
• 5024 includes a 4-circuit negative busbar
63.99 EA
POWERPOST CABLE CONNECTOR
Connect high amperage cables securely. Includes insulator
caps. 48 volts DC maximum. Posts have no amperage
rating because amperage flows between terminals stacked
on the post and is determined by the wire and terminals
used.
398.99 EA
Item#
661-2002
661-2003
701 SURFACE OR RECESS MOUNTED
CONTOUR MANUAL BATTERY MASTER
SWITCH
Mount
Surface or Recessed
Volts
6-48
Size
23/4" x 23/4" x 3"
65.99 EA
4 POSITION - OFF/1/BOTH/2
The 701-S is the most compact selector switch available
on the market. Housed in the same manner as the 701
and includes the same removable side plates and back
cover. While BEP Marine foremost recommends isolated
battery systems as outlined with our distribution clusters,
the 701-S offers a simple economical way of separating
two batteries.
• Rated for 200 amps continuous, 300 intermittent, 1000
cranking
• Panel mount version requires a standard 11/16" cut out
Mount
Surface or Recessed
KEY: Blue Item # =NEW
|
Volts
6-48
Red Item # =HAZARDOUS
Size
23/4" x 23/4" x 3"
Stud
/16" x 7/8''
3 / " x 7/ ''
8
8
5
24.99 EA
24.99 EA
Item#
661-2018
Provides a termination point for extending the length of
outboard harnesses or other conductors.
• Designed for connecting high amperage conductors
• Designed for outboard engine installation when factory
cables need to be extended
• One-piece serrated flange nuts ensure correct and secure
connections
• Continuous Rating Not rated-amperage flows between
terminals stacked on post and is determined by wire and
terminals used.
• Voltage Max. Operating: 48V DC
• Mounting Holes Accepts: #10 (M5) Screws
Size
2.75''L x 1.75''H
39.99 EA
TERMINAL BLOCK
701-S MINI BATTERY SELECTOR SWITCH
Item#
969-701S
Size
3.30'' x 1.75''
3.30'' x 1.75''
DUAL POWERPOST CABLE CONNECTOR
• Compact, lightweight
• Removable key
• Countersunk recesses for surface mount application
• Standard 21/16" (52 mm) hole cut out (same as standard
gauge hole)
• Inside: captive inserts for 3/16" (4.8 mm) nuts providing full
access for cables with no restrictions
• Standard interchange label system
• Molded in high temperature, fiber reinforced plastics
Item#
969-701
149
81.99 EA
| vOversize | dUPS/FEDEX Surcharge
4 Gang
6 Gang
8 Gang
10 Gang
Corrosion resistant construction. Moisture repellent bakelite insulator base. Nickel
plated brass terminals and #8-32 screws. Protective insulator barrier strips. Rated
for 30A @12V.
Item#
Gangs
Size
7.99 EA
50-13561
4
4"L x 15/16"W x 11/16"H
50-13571
6
43/8"L x 15/16"W x 11/16"H
10.99 EA
1
5
11
50-13581
8
5 /2"L x 1 /16"W x /16"H
10.99 EA
50-13591
10
65/8"L x 15/16"W x 11/16"H
11.99 EA
To Our Valued Customers: Prices are subject to change without notice
