UL Catalog 2024-2025 - Flipbook - Page 35
Model Length (A)
ORDERING INFORMATION
2 Hp Variable Speed Submersible Pump Ordering Guide
A typical model designation has up to five components to
define the pump being supplied as follows:
STP Horsepower
2 Hp Variable Speed
XXX YYYYY Z - A - B
STP = These standard variable speed and variable length models are capable of
up to 10% ethanol with gasoline
2 Hp Fixed Speed
IST** = These variable speed and variable length models include alcohol-gasoline
compatibility (up to 85% ethanol, up to 20% Biodiesel, or 100% Biodiesel)
ISTAP** = These variable speed and variable length models include alcohol-gasoline
compatibility (up to 85% ethanol, up to 20% Biodiesel, or 100% Biodiesel) and
Advanced Protection with powder-coated, e-coated, and stainless steel components
2 Hp Fixed Speed
High Pressure
Model Length
Designation
59" – 87"
VL1
90" – 151"
VL2
122" – 213"
VL3
63" – 92"
VL1
94" – 154"
VL2
126" – 218"
VL3
63" – 92"
VL1
94" – 155"
VL2
126" – 218"
VL3
SUBMERSIBLE
PUMPING SYSTEMS
XXX = Basic Model Designation
Model Length
Range
YYYYY = Factory Installed Options
Model designations may include one or more of the following characters:
F = Floating suction adapter (1½" NPT female adapter)
K = Intake filter screen (IFS, factory installed to PMA)
M = MagShell® (flow enhancing, expanded PMA shell)
R* = Model R check valve (24 psi relief/22 psi reset for PLLD)
Z = Pump Motor Horsepower Rating
VS2 = 2 Hp variable speed
A = Model Length (see table)
VL1 = STP variable length range #1
VL2 = STP variable length range #2
(B)
RISER
LENGTH
VL3 = STP variable length range #3
B = Riser Pipe Length (see diagram)
Riser pipe length is expressed as two numeric characters that indicate the total
length of the riser in inches. Riser pipes are available from 7" to 60" in 1" increments
(additional charge for risers 31" or longer).
Notes:
*If not otherwise specified, all models are supplied with standard model check
valve (40 psi relief / 35 psi reset for MLD, TS-LS300, and TS-LS500).
**If not otherwise specified, 2 Hp variable speed pump motor horsepower rating
is implied for IST models.
(A)
MODEL
LENGTH
2 Hp Fixed Speed Submersible Pump Ordering Guide
A typical model designation has up to five components to define
the pump being supplied as follows:
STP XXXXX Y - A - B
STP = Basic Model Designation
XXXXX = Factory Installed Options
Model designations may include one or more of the following characters:
AP = Advanced Protection with powder-coated, e-coated, and stainless steel
components, alcohol-gasoline compatible (up to E85, up to B20, and B100)
(Note standard models up to 10% ethanol capable)
AG = Alcohol-gasoline compatible (up to E85, up to B20, and B100)
(Note standard models up to 10% ethanol capable)
F = Floating suction adapter (1½" NPT female adapter)
K = Intake filter screen (IFS, factory installed to PMA)
M = MagShell® (flow enhancing, expanded PMA shell)
*R = Model R check valve (24 psi relief / 22 psi reset for PLLD)
*W = Model W check valve (16 psi relief / 13 psi reset for PPM4000)
Y = Pump Motor Horsepower Rating
200 = 2 Hp fixed speed
A = Model Length (see table)
VL1 = Variable length range #1
VL2 = Variable length range #2
VL3 = Variable length range #3
B = Riser Pipe Length (see diagram)
Riser pipe length is expressed as two numeric characters that
indicate the total length of the riser in inches. Riser pipes are
available from 7" to 60" in 1" increments (additional charge for
risers 31" or longer).
(Note VL2 models fit 94% of all
known installations)
*If not otherwise specified, all STP models are supplied with standard model check valve (40 psi relief / 35 psi reset for MLD, TS-LS300, and TS-LS500).
35
