EN Catalog 2021-22 - Catalog - Page 223
INTELLIGENT
SUBMERSIBLE
TURBINE PUMPS
FE PETRO® introduced the first variable speed submersible
pump for the petroleum industry in 1995. Since that time,
high volume marketers around the world have realized the
benefits of filling cars faster during peak business periods
that only variable speed submersibles can deliver. Station
size and volumes have continued to grow. To meet the
needs of these high volume retailers, FE PETRO® offers the
intelligent submersible turbine pump, the industry’s highest
performing 4" diameter submersible pump.
HIGHLIGHTS
SPECIFICATIONS
Constant Flow
Depending on peak business requirements, marketers
now have a choice of either 2 hp or 4 hp variable speed
models. 2 hp provides constant 10 gpm (38 lpm) for up to
eight fueling positions operating simultaneously, 4 hp for
up to 12 positions.
Power Requirements
IST® models can only be powered by a MagVFC™ or the
EcoVFC™ controllers:
MagVFC™/EcoVFC™ Design Highlights
The MagVFC™ and EcoVFC™ feature a dual seven segment
display to show diagnostic faults. A serial interface is
standard to connect to INCON System Sentinel™ software for
remote reporting of pump alarms and sharing other pump/
ATG intelligence. The MagVFC™ and EcoVFC™ detect and
display these system conditions:
•
•
•
•
•
•
•
Dry tank (initiates an immediate pump shut-down)
Continuous pump run
Low incoming voltage
Pump motor failure
Short circuit detection
Controller faults
Open circuit detection
2 hp models can operate with single phase incoming
power supply to the MagVFC™.
•
2 hp and 4 hp models operate with three-phase incoming
power supply to the EcoVFC™.
•
Incoming power supply to the MagVFC™ can be 200-250 VAC,
50 Hz and 360-440 VAC, 50 Hz for the EcoVFC™.
•
MagVFC™ outputs a three-phase, variable frequency
signal, valid for FE PETRO® variable speed pumps only.
•
•
•
2 hp max. motor draw: 9 Amps.
4 hp max. motor draw: 15 Amps.
MagVFC™ or EcoVFC™ max. line draw: 20 Amps.
Pump Motor
• 2 hp or 4 hp, variable speed, two-stage centrifugal
type pump motor with integral, automatic, thermal
overload protection.
•
•
Max. flow: 2 hp = 110 gpm, 4 hp = 140 gpm.
•
Available with MagShell®, which results in 45% increased
flow area around motor.
Max. pressure: selectable operating pressure on MagVFC™
or EcoVFC™ between 1.65 bar and 2.9 bar deadhead.
Liquid Compatibility
• Max. liquid viscosity: 70 SSU at 60 °F (15 °C).
SUBMERSIBLE
PUMPING SYSTEMS
For reduced installation cost, a shielded power cable is not
required. Pump protection extends pump life and extended
run fault alerts a condition that may render line leak
detection ineffective. Remote reporting of pump alarms and
sharing of IST® and ATG intelligence further reduce station
operating costs.
•
• IST® models imply alcohol-gasoline compatibility for fuel
mixtures containing diesel fuel with up to 20% biodiesel,
100% biodiesel, up to 85% ethanol with gasoline, and 20%
MTBE, 20% ETBE or 17% TAME with gasoline.
• IST® models can also be used for fuel mixtures containing
up to 5% biodiesel with diesel fuels, fuel oils, kerosene,
Avgas, and jet fuels in a non-gelled pourable state.
• All wetted elastomers are made of a high grade,
fluorocarbon compound.
223