Farmer-Boy-catalog - Catalog - Page 114
Your Best In Value and Customer Support
Cooling
Synergize Cool Cell Disinfectant
Virocid®
A low-foaming disinfectant and is recommended for
use in cool cell systems, evaporative coolers, and other
areas where low-foaming disinfecting and the control
of mold, algae, and the spread of aerosol disease
is a priority. Research indicates that a cool cell pad
impregnated with Synergize Cool will render live PRRSv
non-viable within one minute of passing through pad.
Directions:
®
The most powerful disinfectant! Virocid is
proven effective at disease prevention and
is widely recommended for fighting disease
outbreaks. In addtion to its disease prevention,
Virocid is great for control of algae and slime
forming bacteria in recirculating water cooling
systems and evaporative condensers
• Must be added in the system directly at a point where
uniform mixing and even distribution will occur
• Do not mix with other chemicals or additives
• Severly fouled systems must be chemically or manually cleaned before adding Virocid
• Apply 1/2 oz. of Synergize Cool per 1 gallon of water
• Example: A 100' Cool Cell System holding 300 gallons of water
would take 150 oz.
• Apply 2 times/week (i.e. Monday AM and Thursday PM) as
product is effective for up to 72 hours after application
Directions:
• Initial dose: 2.5 fluid oz. of Virocid per 100 gallons of
water, repeat until algae/slime is under control
• Maintenance dose: 1.23 fluid ozs per 100 gallons of water in the system every 7 days,
Repeat as needed
Part #
99050030
Description
Virocid® 1.33 Gallon
Price
51.78
Qty
48.45 (4)
COOL CELL PADS SERVICE TIPS
• Check for holes and blow out pads once a year
• Pull pumps and drain lines before temperature drops below freezing. If pumps cannot be pulled, put additives in tank to keep water
from freezing
• Return pumps in spring, after threat of freezing has passed. Test the
system
• Check for clogged water outlet holes. (Pads should be wet all over,
not patchy.)
• Remove pads in the winter time
EVAPORATIVE COOLING
MAINTENANCE TIPS
• Maintain clean water -clean well water or chlorinated city water with
proper pH levels
• Check distribution header also for obstructions which can lead to
damaged or clogged pads (0.75 GPM for 6" pads.
• Dry pads - every 24 hours to prevent algae buildup
• Maintain 3-5% water bleed off rate
• Pad and sump areas protected (shaded) - direct sunlight causes
algae growth
• Flush entire system - once a week, during operation to control
mineral levels
• Maintain minimal on/off wetting cycles
• Keep steady amount of water flowing over pads - to help prevent
mineral buildup
• Mineral treatment - used to prevent scale and mineral buildup. Keep
silica levels below 150 ppm
• Algaecide - used to prevent growth on cooling pad
• Brushing off debris - when pads are dry, with a soft brush bristle
brush, followed by complete flushing accumulated fragments of
debris - biannually
• Rotate pads annually
110
Part #
99050868
Description
Synergize COOL 1 Gallon
Price
36.78
Qty
34.35 (4)
Pad Descaler/Nozzle Cleaner
Effective in removal of mineral scale in cool cell pads
and nozzles. Softens and removes deposits in cool cell
pads and nozzles. Use to control calcium and magnesium scale, dissolved iron and manganese,
and sequester alkali metals.
Directions:
• Add 1 gal clean water pH 4-9 to crystals & dissolve
• Prepare working stock solution. Add 1 oz concentrate
per 2 gallons of water
• Meter solution at 1 oz per gallon (1:128)
Part #
99050013
Description
Cleaner 1 Gallon
Price
15.89
Qty
14.58 (4)
Cool Cell Pad Conditioner
Specially formulated, highly concentrated surfactant solution.
Regular use maintains the porosity and wettability of cool cell
materials for optimum water flow. Helps prevent build-up
such as algae, extending pad life.
Directions:
• Usage: 4 oz. every 2 weeks per 50 gallons of water. A typical cool
cell holds 3 gallons per linear foot of cool cell trough
• Example Usage for 100' Cool Cell System: Apply 24 oz. of cool cell
pad conditioner. Repeat every 2 weeks
Part #
99050014
Description
Conditioner 1 Gallon
Price
140.31
Qty
129.09 (4)
Powder Descaler
Removes stubborn mineral deposits in the water
storage system, pumps, water nozzles, spray
deflector, evaporative cooling pads, and drains.
Directions:
• Gently brush dirt and other debris off of dry pads
• Flush systems with water. Check for proper flow
and fix leaks
• Circulate the Powder Descaler for 1 week and dump
rinse the system. Complete again after 1-2 weeks,
then follow up monthly through the season.
• Check for proper flow and fix leaks again
• Usage: 4 lbs. of product treats 100 gallons of water
• Example: A 50 ft. system holding 3 gallons per
linear foot would use 8 lbs. of product
Part #
99050909
Description
Powder Descaler 8 lbs.
Toll Free Order Line: 800-845-3374
Before
After
Price
38.91
Qty
35.79 (4)
